harrypo53
01-12-2010, 01:41 AM
i am trying to install this system myself but want to make sure i know where every wire goes before i start. there are a few i am confused about and need to know where to locate them. i have a good idea on most but still want to double check. knowing all the wires will make this pretty simple i think until the passlock2 part where i cross my fingers and hope my car will reprogram itself with the 10 minute relearn
2002 grand am
4 door
2.2L engine
viper 5901 starter
Primary harness (H1), 12-pin connector
1 * RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT (alarm wires)
(got it)
2 * Red (+) 12v CONSTANT INPUT
(got it)
3 * BROWN (+) SIREN OUTPUT
(got it)
4 * WHITE/BROWN LIGHT FLASH -ISOLATION WIRE - PIN 87a of onboard relay
no clue
5 * BLACK (-) CHASSIS GROUND
(got it)
6 * VIOLET (+) DOOR TRIGGER INPUT
(got it)
7 * BLUE TRUNK PIN/INSTANT TRIGGER INPUT
no connection?
8 * GREEN (-) DOOR TRIGGER INPUT
no connection?
9 * BLACK/WHITE (-) 200mA DOME LIGHT OUTPUT
(got it)
10* WHITE/BLUE (-) REMOTE START/TURBO TIMER ACTIVATION INPUT
no clue
11* WHITE PARKING LIGHT OUTPUT
no clue
12* ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
no clue
AUXILIARY HARNESS (H2)\
1 * LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT
no clue
2 * ORANGE/BLACK (-) 200mA AUX 4 OUTPUT
3 * GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT
no clue
4 * VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
5 * WHITE/BLACK (-) 200mA AUX 3 OUTPUT
6 * WHITE/VIOLET (-) 200mA AUX 1 OUTPUT
7 * GRAY/BLACK (-) DIESEL - WAIT TO START INPUT
not needed
8 * BROWN/BLACK (-) HORN HONK OUTPUT
(got it)
9 * VIOLET/WHITE TACH INPUT
not needed with virtual tach?
10 * DARK BLUE (-) 200mA STATUS OUTPUT
passlock 2 bypass module
11 * PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT
not needed ?
12 * ORANGE (-) 200mA ACCESSORY OUTPUT
not needed
13 * PURPLE (-) 200mA STARTER OUTPUT
not needed
14 * PINK (-) 200mA IGNITION 1 OUTPUT
not needed
15 * GREY (-) HOOD PIN INPUT
(got it)
16 * BLUE/WHITE (-) 200mA REAR DEFOGGER
which wire exactly?
17 * BROWN (+) BRAKE SHUTDOWN
where is brake switch?
18 * BLACK/WHITE (-) NEUTRAL SAFTY INPUT
ground
HEAVY GAUGE, 10-PIN CONNECTOR
1 * PINK IGNITION 1 INPUT/OUTPUT
pink ignition wire
2 * RED/WHITE (+) (30A) FUSED IGNITION 2/ FLEX RELAY INPUT 87
+12v constant ?
3 * ORANGE ACCESSORY OUTPUT
there are two orange wires in ignition harness.....
4 * VIOLET STARTER OUTPUT
car side of yellow wire
5 * GREEN STARTER INPUT
key side of yellow wire
6 * RED (+) (30A) FUSED IGNITION RELAY INPUT
+12v constant ?
7 * PINK/WHITE (+) IGNITION 2 FLEX RELAY OUTPUT
dark green ignition wire?
8 * PINK/BLACK 87a OF IGNITION 2 FLEX RELAY
not needed ?
9 * RED/BLACK (+) (30A) FUSED ACCESSORY/STARTER RELAY INPUT
+12v constant ?
thanks for your help, anything that will help verify what i think i need to do will be awesome
2002 grand am
4 door
2.2L engine
viper 5901 starter
Primary harness (H1), 12-pin connector
1 * RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT (alarm wires)
(got it)
2 * Red (+) 12v CONSTANT INPUT
(got it)
3 * BROWN (+) SIREN OUTPUT
(got it)
4 * WHITE/BROWN LIGHT FLASH -ISOLATION WIRE - PIN 87a of onboard relay
no clue
5 * BLACK (-) CHASSIS GROUND
(got it)
6 * VIOLET (+) DOOR TRIGGER INPUT
(got it)
7 * BLUE TRUNK PIN/INSTANT TRIGGER INPUT
no connection?
8 * GREEN (-) DOOR TRIGGER INPUT
no connection?
9 * BLACK/WHITE (-) 200mA DOME LIGHT OUTPUT
(got it)
10* WHITE/BLUE (-) REMOTE START/TURBO TIMER ACTIVATION INPUT
no clue
11* WHITE PARKING LIGHT OUTPUT
no clue
12* ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
no clue
AUXILIARY HARNESS (H2)\
1 * LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT
no clue
2 * ORANGE/BLACK (-) 200mA AUX 4 OUTPUT
3 * GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT
no clue
4 * VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
5 * WHITE/BLACK (-) 200mA AUX 3 OUTPUT
6 * WHITE/VIOLET (-) 200mA AUX 1 OUTPUT
7 * GRAY/BLACK (-) DIESEL - WAIT TO START INPUT
not needed
8 * BROWN/BLACK (-) HORN HONK OUTPUT
(got it)
9 * VIOLET/WHITE TACH INPUT
not needed with virtual tach?
10 * DARK BLUE (-) 200mA STATUS OUTPUT
passlock 2 bypass module
11 * PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT
not needed ?
12 * ORANGE (-) 200mA ACCESSORY OUTPUT
not needed
13 * PURPLE (-) 200mA STARTER OUTPUT
not needed
14 * PINK (-) 200mA IGNITION 1 OUTPUT
not needed
15 * GREY (-) HOOD PIN INPUT
(got it)
16 * BLUE/WHITE (-) 200mA REAR DEFOGGER
which wire exactly?
17 * BROWN (+) BRAKE SHUTDOWN
where is brake switch?
18 * BLACK/WHITE (-) NEUTRAL SAFTY INPUT
ground
HEAVY GAUGE, 10-PIN CONNECTOR
1 * PINK IGNITION 1 INPUT/OUTPUT
pink ignition wire
2 * RED/WHITE (+) (30A) FUSED IGNITION 2/ FLEX RELAY INPUT 87
+12v constant ?
3 * ORANGE ACCESSORY OUTPUT
there are two orange wires in ignition harness.....
4 * VIOLET STARTER OUTPUT
car side of yellow wire
5 * GREEN STARTER INPUT
key side of yellow wire
6 * RED (+) (30A) FUSED IGNITION RELAY INPUT
+12v constant ?
7 * PINK/WHITE (+) IGNITION 2 FLEX RELAY OUTPUT
dark green ignition wire?
8 * PINK/BLACK 87a OF IGNITION 2 FLEX RELAY
not needed ?
9 * RED/BLACK (+) (30A) FUSED ACCESSORY/STARTER RELAY INPUT
+12v constant ?
thanks for your help, anything that will help verify what i think i need to do will be awesome